• Solarfest 2016

  • Being Smart About Solar

    Before going solar…. consider these points


    So…. you’re thinking of going solar. Congratulations! It’s a big step, and a worthy one.

    By embracing solar power, you help reduce the load on our local energy grid, which cuts down on air polluting emissions and helps us avoid or delay the need to build another power plant. You also offset—perhaps even eliminate—your electricity bill. In short, going solar is good for the planet, good for the community and good for you.

    Your local public electric and gas utility, CPS Energy, has approved an additional $30 million of the community’s dollars for solar rebates. Additionally, Federal government will be offering a 30% Investment Tax Credit until 2020. Being educated so you can choose the best solar option for you means that we can utilize the rebates so that more people can access solar and its myriad benefits. CPS Energy has just implemented some important measures to help protect the safety of customers in the market for solar. However, like any major investment, it’s a important to be well informed about what your options are and what you are purchasing.

    In the spirit of good stewardship, Build San Antonio Green has assembled the following considerations to help you become well-informed about solar. If you want to learn more about how solar technology works, visit the “Solar 101” section of our website, buildsagreen.org.

    1. What size system is right for me?

    Deciding what size system depends on what you would like to accomplish. If you are really into solar and want to do your part to help reduce demand for the community, you may want to have the most solar you can get. If you are looking to reduce your utility bill to save some money, then that is likely not your best option.

    For most people, an ideal solar array would produce just enough power to wipe out their electricity bill on an annual basis. Doing so can still benefit the community by not using valuable power from the grid (and delaying or avoiding the need to build more power plants), and by helping you personally to save money. Look at your electricity bill – how many kilowatt-hours (kWh) did you consume last year? That is the maximum amount of electricity your system should produce to be most efficient.

    When you consume your own solar power to zero out your bill, your local utility pays you approximately $0.098/kWh.* But when you produce excess power and sell it back to the utility, the rate drops to $0.0169/kWh. The most efficient scenario is to buy a solar array that produces just enough power to eliminate your electricity bill.

    In short, bigger is not necessarily better. Keep in mind that a bigger system always entails more upfront costs. So optimize the system size based on your goals, consumption, and budget.

    If your goal is to save some money, then it’s also a good idea to investigate getting an energy audit for your home. You can find a local energy rater who will help you determine how energy efficient your home is. The more efficient your home before you add solar, the smaller system you will need to zero out your bill. It may be more cost effective to take some measures to make your home more efficient and then add a smaller system, decreasing your upfront costs. CPS Energy even offers various rebates for energy efficiency upgrades. Check out www.cpsenergy.com to see if you qualify.


    1.  How do I know if I have the ideal conditions for solar?

    Most smart phones have an integrated compass. Use yours to find the orientation of your rooftop. You can compare what you find with your installer and even ask your installer what the difference in production would be if you had a south-facing roof. East-west facing systems produce 12-15% less energy than south facing ones. If your installer provides a production estimate and return on investment calculation, make sure the estimate for the system is modeled according to your roof orientation and not the ideal south facing ones.

    1. Six hours of sun per day, every day is the industry standard for maximum Return on Investment (ROI.)

    Is your roof so situated that it receives six hours of sun per day, every day, every season? The peak solar window is 10am to 4pm every day all year. Does your roof have six hours of uninterrupted sun?

    If not, your production will be lower and the payback longer. Also, make sure to be aware of any shading issues your roofs might have, whether it is shading from any surrounding trees, or shading from a chimney. A quick look at satellite imagery of your home would be a good place to start. Installers have equipment that is capable of assessing shading patterns at any proposed roof site. Work with your installer so you do not place panels on any shaded areas. It would be a disservice to have a large system, but have half of it covered in shade. And it would mean that you will not meet your maximum production and ROI.



    1. Are high efficient (HE) panels better?

    It may seem logical to have the most highly efficient (HE) solar panels. But again, this depends on your goals. The HE panels cost more.Compare the cost increase to the production increase. Are the panels worth the extra cost? If your goal is to produce as much energy as possible and cost is not a factor, then the HE panels could be right for you. But if you are considering the upfront costs and long term ROI, then they may not offer the best long-term investment.

    As a side note, keep in mind that if you are going after the CPS rebate, all equipment chosen must be new and listed on the California Energy Commission list of approved modules and inverters, which can be found on the CPS Energy website. When you buy a new car with a V8, you can pop the hood to see the engine. How do you pop the hood on a solar project? Ask for the bill of material and check the serial numbers. Make sure you receive the equipment you were promised.

    1. How do I know if I’m getting the best price for my system?

    The solar industry, like many others, has some less-than-reputable businesses. In order to make an informed decision about which installer is right for you, do some research. Rather than going with the first installer you call or find, get several quotes from a few installers. CPS Energy keeps a list of approved installers which you can find on their website. Make sure the installers you are considering are listed.

    1. Get details on the warranties, including one for your roof.

    Installing a solar system will require that holes be drilled in your roof. It’s a good idea to ask your installer if they will guarantee that your roof, built to last 20 – 30 years, won’t be harmed or leak as a result of the installation.

    If you are planning on accessing the CPS Energy Rebate, CPS Energy has certain requirements for warranties. They require that all installed PV systems carry a five-year warranty from the installer. Solar modules must carry a 20-year warranty from the manufacturer, and inverters (the piece of necessary gear in any solar system that converts direct current from the sun to useable alternating current that can be absorbed into the grid and your home) must carry at least a five-year manufacturer’s warranty without battery back-up.


    Know your guarantees and warranties before signing any contracts, and factor them into the ROI of your system.

    The decision to go solar is exciting, and worthy, but it’s also a big financial decision. Being well-informed about your options and working with your installer to make the right choices for your situation and goals is the best way to get the most from your investment. We know you are super excited to get that solar system, but make sure you manage your expectations. Ask your installer about their process and an estimate of when your system should be online.

    *All prices estimates as of March 1, 2016.

    Contributors to this article include: Monika Maeckle, Jacob Eyer, and Kate Rodriguez 

    Solar Links

    Interested in Learning about Solar Options and Getting 3 Free Quotes? Visit our program site: BringSolarHome.com

    About How Solar Works

    CPS Energy Solar Info

    CPS Energy Rebate Info 

  • We are Hiring!

    Build San Antonio Green is looking for an Administrative Director to join our team! We are hoping to find someone soon, so if you are self motivated, outgoing person and you are interested in working in a fun and progressive non-profit environment send us your resume right away. Below you can see the job description. This will be a full time position that does include a benefits package.

    Administrative Director Job Description 


    • Daily,Weekly, monthly, quarterly & annual budget reports to the Executive Director
    • Assist Executive Director with annual budget forecasting and maintain all audit practices
    • Daily accounts receivable, accounts payable, billing & journal entries to budget report & accounting program (Quickbooks Premier)
    • Assist in Accounts Receivables and Payables, Budgets for Events
    • Monthly reconciliation of journal entries to bank statements
    • Compilation of annual end of year financial report to CPA firm for filing of annual IRS Form 990 tax return
    • Fill out annual property tax inventory report for Bexar Appraisal District. Set up payment of annual property tax when invoice arrives. Maintain and update office equipment inventory.
    • Billing and A/R for certifications and Bring Solar Home
    • Provide budget and/or financial reports to vendors, organizations & institutions requesting them
    • Management of financial tracking of government consulting contracts
      • Track staff hours submitted
      • Generate invoices
      • Cost out contracts based on deliverables & staff hours per task
      • Track amounts billed, pending & remaining on contract (report to Executive Director)



    • Process weekly payroll for all staff & set up direct deposit transfers via Quickbooks Payroll
    • Run monthly IRS Payroll Tax report & submit monthly payroll tax deposit to IRS via EFPTS online payment system
    • Run quarterly IRS Form 941 Payroll Tax returns
      • Submit to Executive Director for review & signature
      • Mail report to IRS & retain copy for files & annual EOY financial report to CPA
    • Run quarterly Texas Workforce Commission unemployment tax reports
      • Run report in payroll program (Quickbooks Payroll)
      • File report online with Texas Workforce Commission
      • Set up payment with Texas Workforce Commission if/when payment is owed
    • Track & update any deductions, garnishments, mileage or expense reimbursements for staff payroll. Make sure any supporting documentation is in employee file and make payments as needed to entities.

    Human Resources:

    • Maintain & update all staff personnel records
    • Benefits Administration
      • Act as company liaison with health insurance broker & insurer(s)
      • Shop/broker insurance policies rates for review & approval by Executive Director
      • Assist staff when enrolling and/or renewing participation in health insurance plans
      • Maintain all files (digital & paper) for all insurance policies
    • Maintain & update all BSAG employee governance documents (employee handbook, drug free workplace, grievance policy, job descriptions, etc) & ensure all are in compliance with State & Federal Labor Laws
    • Assist with processing new staff


    Outreach & BSAG Programs:

    • Assist Director of Community Affairs with administrative items and participate in all outreach, workshops, lectures and fundraising events..
    • Assist with errands and/or gathering of supplies as needed for events or meetings
    • Assist in promotion of membership amongst builders, architects, suppliers & service providers in the BSAG membership program
    • Assist Director of Community Affairs in membership database, invoicing and renewal



    • Maintain database, contact lists, digital records & all paper files. Update any or all of these as needed or directed.
    • Analyze offices practices, such as record keeping, forms, office layout, personnel and budgetary requirements, and performances standards to create new systems or revise old systems- (digital and/or hard copy)
    • Act as company liaison with business liability insurance broker (business liability, Director’s & Officer’s Liability, Fidelity Bond & Worker’s Compensation) and Insurance companies.
    • Assist scheduling of meetings, appointments and Board of Directors Meetings as requested
    • Assist in travel & lodging arrangements for out of town conferences attended by staff members
    • Maintain and organize office supplies & equipment
    • Assist the Executive Team in any way needed or directed
    • Answer phones & greet visitors as needed

    Skills & Knowledge

    Applicants must have complete working knowledge and experience with Quickbooks, preferably they will also know Quickbooks Payroll plugin.

    Construction Industry Experience and or Graphic Design background is a plus.

    If you are interested please send your resume to Director of Communications, Jacob Eyer at jeyer@buildsagreen.org

  • Going Green Easy Summer Projects

    Welcome to the BSAG Influencers Blog Series! This is a new series of articles from friends and colleagues from our community discussing topics relating to sustainability and green building in San Antonio. We hope that this series will help provide some perspective and insight into what’s happening on the Green Front right here at home. The articles are meant as conversational in nature and therefore do not necessarily reflect the thoughts and opinions of Build San Antonio Green or it’s staff.
    With that said, Please enjoy this very informative article by one of our good friends at Green Home Realty, Drew McCurdy!
    It’s that time of year again! It’s starting to heat up, the kids are out of school, and you are spending more time in and around your home. If you are a current homeowner or are considering purchasing a home soon, you know how important it is to implement GREEN options. But with all the demands on the budget, you likely are asking how you can afford to be GREEN, where to start investing to realize value, and how to get started. Relax! As a Realtor with GREEN Home Realty who is certified GREEN by the National Association of Realtors, I get these questions frequently from my clients and would like to share how you can easily be more GREEN.   When looking at where to start first, there are a few main areas to consider: saving electricity, conserving water, and reducing waste. One of the largest energy consumers is your central air conditioner and heater. If you are purchasing a new home, make sure you pay attention to the SEER Rating, which stands for the Seasonal Energy Efficiency Ratio. According to Energy.gov, this rating essentially provides the relative amount of energy required to provide a specified amount of cooling for your home. Additionally, for newer homes built after January 26, 2006, this rating must be at minimum 13 or higher. If you are in a home with a system rated lower than 13, it may not be cost-effective to replace the system just yet unless it’s failing. In either case, it’s what controls your air conditioner that can play a huge role…your thermostat!
    Originally, many thermostats were manual. If you left it on, you may have cooled (or heated) too much. If you left it too low, then it would require more energy to get your home to a reasonable temperature. Then came programmable thermostats, which offered slightly better control.
    The challenge with programmable thermostats is that if they don’t have a flexible schedule adjustment, you could still be limited by one programmed schedule and still be wasting energy. Today, there are many more options including self-adjusting/learning thermostats. These thermostats learn your behavior and adjust accordingly. Many can be connected securely to your network for additional control away from home and through your mobile device. Consider a popular model like the Nest Thermostat. This thermostat retails for $249 and can be easily picked up locally at your Home Depot or Lowe’s. Scared of wiring? Don’t fret! Installation couldn’t be easier…even for a novice. Having personally installed myself, instructions are step-by-step. For most installations, it takes less than 15 minutes! There is even an online interactive guide to help you confirm compatibility with your system and walk you through the install process. Customer support is fantastic, should you need it. Using your thermostat is as easy as using your iPhone or Android phone. Not to mention, it looks beautiful in any home and will pay for itself in months!  
    Another big challenge in Texas is living with the heat and seemingly constant water restrictions! During the spring and summer months specifically, it can be increasingly difficult to maintain a beautiful landscape – even with drought resistant plants – when homeowners are restricted to specific days and times to water. Like most people, those schedules don’t always fit so something has to give and it usually is your landscape. Approach this differently to get your desired results. Consider a rain barrel to capture the rainfall off your roof.   As explained by epa.gov, a rain barrel is a type of system that will collect and store excess water as a reserve that would otherwise be lost as runoff. Based off epa.gov’s calculations, in as little as one rainfall you could easily fill an average-sized rain barrel of 55 gallons. This could provide enough water during the peak watering months April – October and as much as 1300 gallons of water, depending upon rainfall! Who wouldn’t want free, unrestricted water?
      Rain barrels vary in size, setup, color, and function. Basic setups, which are fine for most, start as little as $39 and sometimes less. More extravagant systems can be expanded on as budget allows. This provides flexibility to expand your savings as your landscape develops over time. I have personally purchased a few rain barrels locally from Dave The Barrel Man in San Antonio. At $69, I was able to get a 55-gallong barrel with built-in water spigot and removable screened lid – important to ensure insects cannot get to water. Service was fast and friendly and picking them up was easier than going to the grocery store. They are lightweight and I had them setup in minutes upon arriving home. And for those of you wondering if you can water from them directly…yes! Gravity allows water to flow through the spigot. Connect a simple water hose and your neighbors will be jealous as your landscape beautifies your home…not to mention you can wash your car without restriction!   Did you know that according to epa.gov for every 1/8 of an inch gap under a 36-inch door lets in as much air as a 2.4-inch hole in a wall? Now imagine those gaps and cracks around your home.
    Maybe your front door, back door, or garage door has been overlooked for a while? Perhaps around your windows or fireplace you have some gaps you’ve ignored? You don’t think about it, but those add up! Under $20, there are several options available including silicon caulk that comes in a variety of colors that will seal, flex with temperature changes, and complement your home. Door sweeps can be easily installed to begin providing enhanced sealing between your outside doors and the floor. Spray foam can insulate large crevices indoors and out. And light switch and socket plate insulators may be beneficial. All can be found at local hardware stores.
    Thought about going solar but not ready to go all out yet? Start with something simple! For about $200, you can purchase solar attic fans to replace those squeaky turbines that are probably rusted, broken, and only spin when there is actually consistent wind. Solar attic fans provide cool air circulation in your attic using the sunlight. Imagine that, use what causes your attic to heat up to actually cool it down, save energy, and for free after your initial installation. There are many places to purchase the fans including Costco, Home Depot, and Lowe’s. There are several varieties to choose from to suit your taste. To know how many you need, you can check out a suite of calculators online that allow you to plug in your attic square footage, such as the calculator at solar-attic-fan-info.com. You can install yourself if you are comfortable making a small hole in your roof or, for a nominal fee, a licensed installer can do it for you if you’d rather not get on a ladder.
    Once installed, you will notice a dramatic difference in the temperature of your attic as hot air is being expelled consistently. This in turn reduces the strain on your A/C and thus your bill as it keeps the cooled air cooler as it travels through the ducts into your home. This one potentially can have a multiple times savings impact! Add an attic tent for more!
      Several other projects exist at varying levels that include rebates which you can take advantage of by visiting cpsenergysavers.com. Currently, A/C, attic insulation, solar, and natural gas rebates exist to name a few. Visit saws.org/conservation to view a variety of indoor/outdoor rebates that exist for more projects at varying levels. Outdoor rebates currently include patioscape, landscape, irrigation design, and swimming pool filters. Indoor rebates currently include free water-efficient fixtures. It’s definitely worth checking out these rebates, especially if you are planning to do some of these projects anyways and are on a budget.   More and more, buyers are looking to purchase energy efficient homes and sellers are looking to implement GREEN enhancements for greater resale value. It’s a known fact in the real estate industry that homes with GREEN technology sell faster and closer to the list price. It’s a win-win for everyone! So if you’re looking to start some summer projects and didn’t quite know where to start, consider this information and make a list to prioritize what would be most beneficial for your specific needs and budget. Start enjoying your improvements and saving while you’re in your home and having it more marketable should you ever decide to sell or rent your home in the future. And if your looking for a home, know that these projects can be factored into an offer to make your home more efficient and enjoyable once you move in. Being GREEN doesn’t have to be about spending money, it’s about educating yourself to understand the many options you have in reducing waste and conserving. And while you’re enjoying your “green savings,” let everyone else be “green with envy.”

     Drew McCurdy, REALTOR, GREEN, CNE of Green Home Realty, LLC


    If you are interested in participating in the blog series please contact Jacob Eyer the Event & Outreach Coordinator at Jeyer@buildsagreen.org
  • District-Scale Sustainability

    Welcome to the BSAG Influencers Blog Series! This is a new series of articles from friends and colleagues from our community discussing topics relating to sustainability and green building in San Antonio. We hope that this series will help provide some perspective and insight into what’s happening on the Green Front right here at home. The articles are meant as conversational in nature and therefore do not necessarily reflect the thoughts and opinions of Build San Antonio Green or it’s staff.
    With that said, Please enjoy our very first article in this series by Heather Holdridge!

    I have worked with energy and sustainability issues for building projects for the past eight years and have been intrigued by the interconnection between these individual buildings and other elements of the built environment (neighboring buildings, utilities, people, transportation, etc.).  The highest potential for energy and water savings occurs at this interconnection, yet building professionals typically do not get the opportunity to work on projects beyond the individual building scale.  When Architecture 2030 launched “2030 Districts” a few years ago, I took notice, as it seemed like a great model for San Antonio to apply in a unique way.

    Over the past few months, a group of local architects, activists, and properties owners have formed a San Antonio 2030 District Exploratory Committee.  San Antonio will be the first 2030 District to have a boundary that is linear; The boundary will follow the San Antonio River through downtown, stretching from Brackenridge Park in the north to Roosevelt Avenue in the south, and will cover most of downtown between I-10 and I-35.  Within these borders are many of the large downtown offices and hotels, the development at Pearl, UTSA’s downtown campus, and over 5 million square feet of city-owned properties. The San Antonio 2030 District will also be the first 2030 District to incorporate land use goals into its targets, and the first to allow residential properties to participate.

    The first 2030 District was formed in Seattle in 2011, when a group of architects was inspired by tapping into the incredible potential to decrease energy consumption of existing buildings.  133 buildings totally 28 million square feet have joined, which accounts for 37% of the square footage within the district boundary.  So far, the Seattle 2030 District has reduced its energy consumption by 21%, its water usage by 7%, and its transportation carbon emissions by 22%.

    A 2030 District is a defined area in a city where member building owners are committed to the goal of reducing consumption of energy, water, and transportation emissions by 50% by year 2030.  2030 District members are encouraged to share their utility bills as well as proven strategies for improved building performance.  As building owners begin to see improvement in their energy performance and a decrease in their utility bills, more buildings in the District will be encouraged to join.


    The motivation behind sharing utility data is that people tend to have a fatalistic view of paying bills.  That is, many of us receive a bill and pay it without giving much thought to the numbers.  Once District members share consumption data, individual buildings can compare their own energy use against similar buildings in the immediate area and many will implement strategies to realize potential savings.  At the same time, buildings that use less energy can disclose their best practices.  Without this ability to compare, buildings might consume 2 or 3 times more than similar, nearby buildings and never know about the potential savings.

    This district-scale approach to sustainability requires collaboration, leveraged financing, and shared resources through unique public/private partnerships.  Property owners and managers can come together with local governments, businesses, and community stakeholders to create a business model for urban sustainability.  Together, they can develop and implement creative strategies, best practices, and verification methods for measuring progress towards a common performance goal.


    Thirteen building owners and property managers (Alamo Architects, Alternivest, AREA Real Estate, Cleary Zimmermann Engineers, MWM and Associates, OCO Architects, Overland Partners, USAA Real Estate Company and Peloton Commercial Real Estate for One Riverwalk Place, San Antonio Housing Authority, San Antonio River Authority, Zurich International Properties, Lake|Flato Architects, and The Brooklynite) have signed on so far, and San Antonio could become the sixth official 2030 District in the nation once we formalize an agreement for 501c3 partnership. 

    For the San Antonio 2030 District, property owners/managers will not be required to achieve the goals of the District by legislative mandates, or as individuals.  Rather, adopters will achieve the San Antonio 2030 District goals as a collective group of property owners, property managers, and developers because full participation in the District brings collaboration, shared resources, and financing options that will make high-performance buildings the most profitable building type in San Antonio.  There are no fees for San Antonio 2030 District membership at this time.

    Adopters support the goals of the San Antonio 2030 District, which are to meet the following performance goals on a district-wide scale:

    Existing buildings and infrastructure operations:

    • Energy use: A minimum 10% reduction below the national average by 2015, with incremental targets, reaching a 50% reduction by 2030
    • Water use: A minimum 10% reduction below the national average by 2015, with incremental targets, reaching a 50% reduction by 2030
    • CO2­e of auto and freight: A minimum 10% reduction below the current District average by 2015 with incremental targets, reaching a 50% reduction by 2030
    • Land Use: A minimum of 10% retrofits to include low-impact development best management practices by 2015, with an incremental target of reaching 50% of retrofits by 2030

    New buildings, major renovations, and new infrastructure:

    • Energy use: An immediate 60% reduction below the national average, with incremental targets, reaching carbon neutral by 2030
    • Water use: An immediate 50% reduction below the current national average
    • CO2e of auto and freight: An immediate 50% reduction below the current District average
    • Land use: A minimum of 10% of plats to include low-impact development best management practices by 2015, with an incremental target of reaching 50% of plats by 2030

    The San Antonio 2030 District also supports sustainable land use and management practices and low impact development to protect water and air quality throughout the District boundary.


    Adopter Benefits:

    The San Antonio 2030 District is in the process of developing tools which will be available to property owners, property managers, or developers who become adopters:

    • Operational cost savings: The primary direct benefit of making progress toward the District goals
    • ENERGY STAR Portfolio Manager: Assistance with account setup and initial upload of utility data, and ongoing Portfolio Manager training as required
    • Initial benchmarking: Confidential analysis on building performance data in relation to District goals as well as similar building types within the District and nationwide
    • Preliminary assessment: Breakdown of cost and resulting savings of efficiency strategies to meet District goals
    • Access to and guidance for financing opportunities: Information on utility incentives, tax incentives, available financing options (such as ESCo, PACE, performance contracting, etc. as well as traditional mechanisms), and connection to professional partners in the energy retrofit finance sector
    • Founding adopters: The first ten adopters in the San Antonio 2030 District will be highlighted as founding adopters on the San Antonio 2030 District website and may use this designation for marketing purposes
    • Forum discussions: Informal and formal gatherings will be organized to provide adopters the opportunity to share information and best practices


    Adopter Contributions:

    In exchange for adopter benefits, adopters are asked to participate in the development of the District in the following ways:

    • Sharing of performance data: Confidential sharing of building energy use, water use, and transportation management plan data with the SA2030D Advisory Committee.  Aggregate data about the District will be made publicly available but no individual building will be identified.
    • Participation in Portfolio Manager: Use of ENERGY STAR Portfolio Manager to track monthly energy use for each building
    • Lessons learned and case studies: Share insights in best practices, lessons learned, and case studies with the SA2030D Advisory Committee to help raise the level of performance across the District
    • Support for the San Antonio 2030 District Board of Directors (optional): Participation in District decision-making, evaluation of District membership criteria for property owners and stakeholders, mentorship for small/sole proprietor property owner and managers


    If you own or manage a property in or near the San Antonio 2030 District, please contact our group so we can talk about signing up for the initiative.  This is a landmark opportunity for San Antonio to take the national stage for its leadership in sustainability, as our approach will demonstrate the city’s unique culture of collaboration.

    HHoldridgeHeather Gayle Holdridge, LEED AP BD+C, EIT, Associate AIA is the Sustainability Manager at Lake|Flato Architects, a San Antonio-based design firm focused on timeless sustainable architecture that is rooted to its place.  You can follow the firm’s blog at www.lakeflatodogrun.com.  Heather is also a member of Build San Antonio Green’s Technical Advisory Group. 

    If you are interested in participating in the blog series please contact Jacob Eyer the Event & Outreach Coordinator at Jeyer@buildsagreen.org
  • 2013 in Review

    BlogGFX02-Splash copyHappy new year from Build San Antonio Green!  A new year means new possibilities, new features, and new homes!  This is the first of one of our new features – the Build San Antonio Green blog.  We’ll be posting useful and interesting information about the goings on in the world of green homebuilding, our program, and other tidbits about San Antonio acceleration to one of the greenest and most sustainable cities in the United States and the world.

    2013 was a watershed year for us, and we’re looking forward to an even more successful year in 2014 – more green homes, more energy savings, and a greener, more sustainable future for San Antonio.

    • Last year Build San Antonio Green was thrilled to welcome Meritage Homes to our program.  The most recent production builder to commit 100% of homes in San Antonio to our program, they have earned 45 certifications to date.  We expect Meritage to add several hundred homes this year.  With each one Build San Antonio Green certified,  Meritage is demonstrating a commitment to our program and to efficient, high-performance homes for San Antonio.
    • In July, we were proud to hold our second annual Green Home Tour.  This year, the Tour featured an eclectic mix of homes, builders, and neighborhoods across San Antonio – from Southtown, King William and Lavaca to the latest features from green production builders on the northside, the 2013 Green Home Tour had something for everyone. The 2014 Green Home Tour looks to be even more exciting – with so many great infill projects in addition to the cutting edge offerings from green production builders, all facets of green building will be well represented
    BlogGFX1-GHT copy

    All green, all cool! A few of the homes on the 2013 Green Home Tour: clockwise from top left: Quail Run, Norwood, Amorosa, Claudia

    • BSAG also enjoyed playing a large role in the 2013 Parade of Homes.  The second all green Parade was held in Cibolo Canyons, and featured cutting-edge design and features in beautiful, functional, BSAG certified green homes from some of south Texas’ leading custom home builders.  Highlights included River Oaks Home’s project, earning the Greenest Home award.
    • We were also extremely proud to be chosen as the recipient of the NAHB’s 2013 Advocate of the Year. We are thrilled to receive the national recognition this award conveys, and extremely proud that our efforts and accomplishments have been recognized by our peers.
    Anita & Lina accept our award at the EcoDisco

    Anita & Lina accept our award at the EcoDisco

    Finally, the most exciting news of 2013: it was Build San Antonio Green’s most successful year of certifications to date!  We set an all-time record for certifications in a single year with 1065 projects certified and brought our grand total to more than 2500 total certifications. We’ve saved enough energy to run 2400 average San Antonio homes for an entire year.   

    Our successes are possible only because of the great support we receive.  Our stakeholder organizations, with their leadership; homebuilders choosing to certify their homes through our program; homebuyers demanding high-performance and efficiency, and all those interested in and supportive of green building are each crucial to our success.  We are proud that San Antonio has thoroughly embraced residential green building, and in particular, the Build San Antonio Green program.  Here’s to an even greener 2014!

    We’re social!  Follow us!

    FB-f-Logo__blue_512   Instagram  Twitter_logo_blue